润滑油招商加盟1、要考虑到润滑脂的防锈处理特性 应用于滚动轴承内的植物油脂务必具备防锈处理实际效果,防锈油最好是能不溶解水.植物油脂应具备优良的粘合力,并能够在不锈钢板材表层产生一层层浮油.

To consider the anti-rust treatment characteristics of grease, vegetable oils used in rolling bearings must have the actual effect of anti-rust treatment. The best anti-rust oil is insoluble water. Vegetable oils should have excellent adhesion and can produce a layer of oil slick on the surface of stainless steel sheets.

2、考虑润滑油的机械稳定性

2. Considering the Mechanical Stability of Lubricating Oil

油脂在机械加工时会变软,导致泄露.正常运行时,油脂会由轴承座甩到轴承内.如果油脂的机械稳定性不够,运转过程中,会使油脂的皂的结构产生机械性崩解,造成油脂被破坏,从而失去润滑作用.

Oil will soften during mechanical processing, leading to leakage. Normally, oil will be thrown from the bearing seat to the bearing. If the mechanical stability of oil is not enough, the structure of oil soap will be mechanically disintegrated during operation, causing oil to be destroyed, thus losing lubrication.

3、考虑润滑油的油封

3. Oil Seals Considering Lubricating Oil

油封是必需的保护轴承和润滑剂免受外来污染的屏障,轴承运转过程中,不论杂物或湿气都不能渗入轴承内,以防造成对其破坏.

Oil seal is a necessary barrier to protect bearings and lubricants from external pollution. During the operation of bearings, no matter sundries or moisture can penetrate into bearings to prevent damage.

正确的安装保养是发挥轴承最长使用寿命的重要因素.同时,必须注意轴承的清洁度、轴承选择的正确性和选用适当的安装与保养工具.另外,轴承必须防止受到污染物和湿气的污染,并保证有正确的被安装和润滑.故轴承配列的设计、油封的状况、润滑剂的型式及润滑周期,乃至专门的保养皆扮演着相同而又重要的角色.

Correct installation and maintenance is an important factor for the longest service life of bearings. At the same time, attention must be paid to the cleanliness of bearings, the correctness of bearing selection and the selection of appropriate installation and maintenance tools. In addition, bearings must be prevented from contamination by pollutants and moisture, and ensure correct installation and lubrication. Period and even special maintenance play the same and important role.

4、考虑润滑油的混合

4. Consider the mixing of lubricants

决不要把不能相容的油脂混用,如果两种不相容的油脂混用,通常其稠度会变软,最后可能会因油脂容易流失而造成轴承的损坏.如果你不知道轴承原先使用的是哪一种润滑脂,则必须先彻底清除轴承内外的旧油脂,方可添加新油脂.http://www.sdpsrhy.com

Never mix incompatible oils. If two incompatible oils are used together, their consistency will usually soften and eventually the bearing may be damaged due to the easy loss of grease. If you do not know which kind of grease the bearing used to be, you must thoroughly remove the old grease inside and outside the bearing before adding new grease.